LOW VOLTAGE FLUSH MOUNTING PLATES and TEMPLATES
SINGLE GANG LOW VOLTAGE PLASTIC FLUSH MOUNT DEVICE (LV1)
Single Gang Plastic Flush Mount Device
Our Plastic Low Voltage Flush Mount has all its parts already assembled!
All YOU have to do is turn the screwdriver!
The arms automatically turn into position to hold the mount to the wall. Keep turning the screwdriver until the screws are tight. That's All!It's NOT GOING TO MOVE after you tighten the screws!
Works in 1/4 inch to 1 inch Drywall or Panelling.NON-CONDUCTIVE PVC
FREE Level / Template with every 100 Low Voltage Mounting Plates...
Or... Get 100 Single Gang Low Voltage Mounting Plates for 92 cents each!Part Number: CHM3K Price: $1.19 ||| 40+ Price: $0.98
Double Gang Low Voltage Plastic Flush Mount Device
Works great for Alarm Keypads!
Our Plastic Low Voltage Flush Mount has all its parts already assembled! Just tighten the screws!
NON-CONDUCTIVE PVC
Our Level / Template works great for Single or Double Gang Mounting Plates
Part Number: CHM3J Price: $1.39 ||| 40+ Price: $1.05
Template / Level for Low Voltage
Plastic Flush Mount Device
Works on SINGLE and DOUBLE
Gang Flush Mounts!
The FASTEST and EASIEST way
to make your installation
Look Professional!
Get one FREE Level / Template with every 100 Single Gang Plastic Flush Mounts at 98 cents each!
Part Number: CHM3O Price: $9.95
Template / Level with Tape Measure
for Low Voltage Plastic Flush Mount Device
Works on SINGLE and DOUBLE Gang Flush Mounts!Swiveling Tape Measure lets you put the Low Voltage Flush Mount Device exactly 12” from the floor, at outlet level.
Part Number: CHM3I Price: $15.95
Screw-In Single Gang Metal Flush Mount DeviceFor the Old-Timers who like putting screws through their fingers.
For old work.CONDUCTIVE METAL
Part Number: CHM1S Price: $0.89 ||| 40+ Price: $0.79
SCREW-IN Plastic SINGLE GANG LOW VOLTAGE FLUSH MOUNT DEVICE
Screw-In Single Gang Plastic Flush Mount Device
for New ConstructionScrews Included.
NON-CONDUCTIVE PLASTIC
Part Number: CHM3M Price: $0.59 ||| 40+ Price: $0.48
NAIL-IN Plastic SINGLE GANG LOW VOLTAGE FLUSH MOUNT DEVICE
Nail-In Single Gang Metal Flush Mount Device
for New ConstructionNails not included.
NON-CONDUCTIVE PLASTIC
Part Number: CHM3P Price: $0.51 ||| 40+ Price: $0.46
1/2 Inch Thinwall Conduit BushingKeeps cable jacket from getting ripped on stubbed pipes.
Now required by some electrical inspectors.
NON-CONDUCTIVE PLASTIC
Part Number: KIT1B Price: $6.51
Same as 1/2 Inch Bushing, above, for 3/4 inch Thinwall Pipe.
NON-CONDUCTIVE PLASTIC
Part Number: KIT1C Price: $9.59
7/8 Inch Plastic BushingKeeps the cable jacket from getting ripped on holes you drill in headers and studs.
NON-CONDUCTIVE PLASTIC
See our 7/8 Inch Stepped Bit, below...
Part Number: KIT1G Price: $8.99
7/8 Inch Stepped BitThe Fastest and Easiest way to drill holes for cable in studs and headers.
Part Number: HND1T Price: $36.95
TOP-SLIDE
Suspended Ceiling
Cable Guide
2 Pack
Prevents cable from snagging on the corners of the grid, and makes pulling a tangle-free easy one-man job.
Snaps right over the ceiling grid, and pops right off when you're done. Put one at each end of the pull (sold as a 2-Pack).
Raised ends keeps the cable on the Top-Slide to prevent snags and tangles.
Part Number: HND4B Price: $16.95 ||| 10+ Price: $15.95
The Pulling Elbow™
NEW Time Saving Patented ToolThe Pulling Elbow™ allows you to pull cable safely around corners.
6" Radius allows one man to pull cables around a corner, while protecting CAT5 and CAT6 cables from being bent to the point that they won't run at full speed.
• 2" Smooth Pulling Tunnel for running cables has a slot so the cables can be removed after you go around the corner.
• 11.5" by 11.5" "L" Shaped
Heavy Duty ABS Plastic Tool.• Pulling Tunnel holds up to 25, CAT5 / CAT6 or up to 5, 25 Pair Cables.
• Lots of Holes for Easy Mounting with Tie Wraps, Scrap Wire, Beam Clamps or Screws.
Feed cable from boxes
straight up into
The Pulling Elbow™Lots of Holes For Mounting
Use Beam Clamps to Mount It
Use Tie Wraps to Mount It
Wood Screw Mounting
Tie Wrap Mounting
Use Vise Grips for Mounting
If there's no
easy way to
run the cable
in the direction you want...
Make it easy on yourself by using
The Pulling Elbow™There are some jobs where leaving it in the ceiling is the cheapest way to go! NOTE: Use a single 14" Tie Wrap, or put two 8" Tie Wraps together to close the ends of the Tunnel.
Each end of the Tunnel has a convenient slot to hold a standard width Tie Wrap.
Just snip the Tie Wraps at the two ends of the Tunnel to remove the cables, or leave The Pulling Elbow™ in the ceiling.
If you're using more than one Pulling Elbow™ to go around two or more corners (at once), you'll probably need someone paying out the cable from the boxes to help you.
Use our Extra Heavy Duty Black 18" Tie Wraps (below) for easy mounting!
Part Number: TOH4O Price: $25.95 ||| 3+ Price: $24.95
This is one heck of a Tie Wrap!
Extra Heavy Duty 18" Tie Wrap compared to Standard 8" Tie Wrap
Sold in a Bag of 100
Part Number: MSC3J Price: $16.95
Part Number: SWI4P Price: $3.00
Part Number: SWI4H Price: $3.00
Part Number: SWI4D Price: $3.00
Part Number: SWI2D Price: $5.49 ||| 10+ Price: $5.29
Tunnel Type Tie Wrap Mount... The Fastest and Easiest to Use!
Sold in Bags of 100 Natural Color Mounts
Part Number: SWI4Q Price: $6.99
Tie Wrap Mount - Black Color
Black Tunnel Type Tie Wrap Mount
Sold in Bags of 100 Black Color Mounts - Same as Natural Color Mount (Above)
Part Number: SER8N Price: $9.95
Part Number: SWI4G Price: $7.99
Part Number: SER8M Price: $12.50
8" with Mounting Hole
Only Available in Natural Color
Sold in Bags of 100 Tie Wraps with Mounting Hole
Part Number: SWI4F Price: $5.50
Part Number: SWI4R Price: $5.99
Part Number: SER4K Price: $2.99
Part Number: SER4J Price: $2.99
Teflon Tie Wraps are Required in Air Plenum Return Ceilings
When standard Tie Wraps burn, they lot off toxic gas. If they're in a ceiling that's used for the air return on the HVAC system (where the returns aren't ducted), they will distribute the toxic gas to other spaces that aren't on fire, where the people will die (even though there's no fire). You would use Teflon cable in air plenum return ceilings, for the same reason.
Teflon doesn't let off toxic gas when it's burned, so it's safe to use in the plenum return to bundle cables. You don't want to use in premises with a ducted return, since they're incredibly expensive!
8" Teflon Tie Wraps
Standard size Tie Wrap with a special
Turquoise Color indicating they're for
Plenum use.
8" Teflon Tie Wrap
100 Quantity
Part Number: SWI4E Price: $47.50
11" Teflon Tie Wrap
100 Quantity
Part Number: SWI2T Price: $64.95
With Police Style Metal Belt Clip
Holds 8" or 11" Tie Wraps
Velcro Flap
Part Number: HND1S Price: $10.95 ||| 3+ Price: $9.95
Part Number: SER8O Price: $13.95
Black, Red, Orange,
Yellow, Blue, Violet,
Gray, WhiteCan be screwed to a wall, backboard,
or rack uprightsAll sizes are sold in Rolls of 10
12" Velcro Tie Wraps
Black Only... for Bigger Bundles
Sold in Rolls of 10
Part Number: SER8P Price: $8.99 ||| 10+ Price: $7.99
8" Velcro Tie Wraps
Black
Sold in Rolls of 10
Part Number: SER8E Price: $5.99 ||| 10+ Price: $5.79
8" Velcro Tie Wraps
Red
Sold in Rolls of 10
Part Number: SER8F Price: $5.99 ||| 10+ Price: $5.79
8" Velcro Tie Wraps
Orange
Sold in Rolls of 10
Part Number: SER8G Price: $5.99 ||| 10+ Price: $5.79
8" Velcro Tie Wraps
Yellow
Sold in Rolls of 10
Part Number: SER8H Price: $5.99 ||| 10+ Price: $5.79
8" Velcro Tie Wraps
Blue
Sold in Rolls of 10
Part Number: SER8I Price: $5.99 ||| 10+ Price: $5.79
8" Velcro Tie Wraps
Violet
Sold in Rolls of 10
Part Number: SER8J Price: $5.99 ||| 10+ Price: $5.79
8" Velcro Tie Wraps
Gray
Sold in Rolls of 10
Part Number: SER8K Price: $5.99 ||| 10+ Price: $5.79
8" Velcro Tie Wraps
White
Sold in Rolls of 10
Part Number: SER8L Price: $5.99 ||| 10+ Price: $5.79
Super Light 15" Fiberglass Fish Tape
Goes STRAIGHT up or Down a Wall!
12" diameter PVC case is both light and easy to carrySmall enough to carry in your luggage for out-of town jobs!
The SECRET is that it's made exactly like a 1/4" Steel Fish Tape...
1/4" Wide and 1/8" Thick!
1/4" Wide
1/8" Thick
Feed the flat 1/4" section up or down the wall (facing you) until
you hit the header or floor, then fish the included 8" chain (with a
ring to tie the cable onto) out of the hole.The 1/4" Fiberglass Fish goes straight up or down - it doesn't go
off to the side and get lost in the wall!
Makes fishing walls a quick and easy one-man job.8" Ball Chain with a Cable Ring on one end, and a Bullet Nose with a Hole on the other end.
It's definitely the fastest and easiest way to fish an insulated wall, or fish a stubbed pipe!
A little history:
Although phone men have been trying to fish both insulated and un-insulated walls with 1/8" fish tapes for years, they quickly found that the fish would simply coil up inside the wall, and pretty much never come out. That's because the 1/8" fish retains it's coiled memory, so it coils up inside the wall just like it did when it was stored.
In the early 1980's Harris Seltzer, a phone man I worked with at General Dynamics, showed me the magic of the 1/4" fish. It's twice as wide as the regular 1/8" fish (the 1/8" fish was made for fishing pipes, not fishing walls). The extra width and weight of the 1/4" fish helps it to stay flat after it's uncoiled (unlike the 1/8" fish). The extra width means you can feed the fish out along on a suspended ceiling and it will go straight... and you can fish either up or down a wall - and the fish goes straight up or down.
The problem with the 1/4" steel fish was that it was difficult to uncoil and the coil back up, and it's heavy. A new technology has allowed a 1/4" Fiberglass Fish to be made with all of the benefits of a steel fish - and none of the drawbacks!
It's light, easy to carry, easy to coil and uncoil from its PVC case, and there's no oil or rust to come off on your hands.
Try one today! Like all of our products, there's a 30 Day Moneyback Guarantee.
NOTE: The unique 1/4" by 1/8" fiberglass material, which is why this fish goes straight up or down in the wall, is made in Australia. The price of this fish is now quite a bit higher than it was in the past because of the US dollar losing value to the Australian dollar. We have to pay them more US dollars now, in order for them to get the same value in Australian dollars.
Part Number: CID8D Price: $69.95 ||| 3+ Price: $67.50
It's the Smallest 16' Extending Pole
you've ever seen!
Collapses to a little over 2', so it even fits in a Tool Bag!
Only weighs 2 pounds!
Non-conductive fiberglass. Each section locks into place with friction.
Small enough to carry in your luggage for out-of town jobs!
Part Number: CID8Q Price: $94.99 ||| 3+ Price: $89.00
26' TINY EXTENDING POLE
Collapses to 3'... Only weighs 3.3 pounds!
Non-conductive fiberglass. Each section locks into place with friction.
Part Number: CID8P Price: $109.95 ||| 3+ Price: $105.00
Orange Sticks... PVC Coated Fish Rod Kit
Only $82.95
Five 6' Sections
Screw Together
To Go 30 Feet!Special Shoulder on Threaded Ends Prevents the Stud from Breaking...
Even if Hand Tightened!
3/16" Diameter PVC Coated Fiberglass Rods... the PVC Coating Resists Fiberglass Splintering Optional Eggbeater Head $14.95
The rods go where you want with a flick of your wrist...
The Eggbeater Head helps the rods jump over obstructions** View Old Style Green Rods in Ceiling **
Open a ceiling tile, then open another one 30 feet away. Feed your Orange Sticks in the direction of the open tile, flicking your wrist if it stops. Watch it come out the open tile a few seconds later. It's that simple!
Now Better Than Ever...
The combination of the Orange PVC Coating over the Fiberglass Rod, and the Shoulder on the Super Strong Male and Female Ends make this new and improved Fish Rod Kit the Best Ever!
Five Orange 3/16" diameter 6' flexible rods screw together for to make a 30 Foot Fish Rod... or put two together to go 60 Feet!
Put 2 sections together to fish up 12' insulated walls!
This tool is a real money maker! Includes carrying case: $82.95.
Orange Stick Accessory Kit: $29.95
18" Flexible Magnet to grab the Fish chain: $10.95
Part Number: CID8A Price: $76.95 ||| 3+ Price: $72.50
Only $82.95
Five 6' Sections
Screw Together
To Go 30 Feet!Special Shoulder on Threaded Ends Prevents the Stud from Breaking...
Even if Hand Tightened!
3/16" Diameter PVC Coated Fiberglass Rods... the PVC Coating Resists Fiberglass Splintering Optional Eggbeater Head $14.95
The rods go where you want with a flick of your wrist...
The Eggbeater Head helps the rods jump over obstructions** View Old Style Green Rods in Ceiling **
Open a ceiling tile, then open another one 30 feet away. Feed your Orange Sticks in the direction of the open tile, flicking your wrist if it stops. Watch it come out the open tile a few seconds later. It's that simple!
Now Better Than Ever...
The combination of the Orange PVC Coating over the Fiberglass Rod, and the Shoulder on the Super Strong Male and Female Ends make this new and improved Fish Rod Kit the Best Ever!
Five Orange 3/16" diameter 6' flexible rods screw together for to make a 30 Foot Fish Rod... or put two together to go 60 Feet!
Put 2 sections together to fish up 12' insulated walls!
This tool is a real money maker! Includes carrying case: $82.95.
Orange Stick Accessory Kit: $29.95
18" Flexible Magnet to grab the Fish chain: $10.95
Part Number: CID8B Price: $29.95
Noodle Fish Chain: $7.95
Unequivocally the World's Best Fish Chain! 10 feet long. Fish up and down walls. For non-insulated, paper or foil backed walls. Tie the wire on thru a hole at the end. This fish chain doesn't tangle, special super strong thin ball chain will slither thru most anything...then back into its Shirt Pocket Pouch.
Drop it down the wall, make a 3/8" hole, stick the Magnetic Retriever in, and wiggle it around. The Chain globs onto the magnet and you pull it out of the wall!
If drywall is mushroomed into wall, use our 9" Hook Wire to grab chain off magnet!
18" Flex Magnetic Retriever: $10.95
9" Hook Wire: $3.99
Telescoping Pocket Fish w/ pocket clip, 4" long, 21" extended: $9.95
NOTE: On the Spring Steel Hook Wires and Fish Wires, both ends bent in the same direction so you know which way your hook is facing!
18" Hook Wire: $4.99
36" Fish Wire: $5.25
Part Number: TOO2C Price: $7.95
18" Flex Magnetic Retriever: $10.95
Part Number: TOO2N Price: $11.95
9" Hook Wire: $3.99
Telescoping Pocket Fish w/ pocket clip, 4" long, 21" extended: $9.95
NOTE: On the Spring Steel Hook Wires and Fish Wires, both ends bent in the same direction so you know which way your hook is facing!
18" Hook Wire: $4.99
Part Number: TOO2L Price: $3.99
9" Hook Wire: $3.99
Telescoping Pocket Fish w/ pocket clip, 4" long, 21" extended: $9.95
NOTE: On the Spring Steel Hook Wires and Fish Wires, both ends bent in the same direction so you know which way your hook is facing!
18" Hook Wire: $4.99
Part Number: TOO2M Price: $4.99
Telescoping Pocket Fish w/ pocket clip, 4" long, 21" extended: $9.95
Part Number: TOO5T Price: $9.95
630-980-7710
Copyright © 2010 Mike Sandman Enterprises, Inc.
